Inserting a Lace Trim Tutorial

Hi, my name is Katherine Sheers, I’m a lingerie designer by trade so I was overjoyed when I heard July is Sewcialist Lingerie Sewing Month! My background does lend me a certain bias towards all things lace and silk, but objectively I believe that lingerie making has something to offer every level of sewer, from the complete novice through to someone with years of experience looking for a new challenge.

I wanted this guest post to be relevant to as many sewers as possible, so I’m going to show you a simple technique which can be used to beautiful effect across a number of garments, regardless of how basic or advanced they may be.

For this example I’ll be using the ‘Pretty as a Picnic’ mini from my book The Secrets of Sewing Lingerie. They’re very simple knickers, made from a rigid fabric cut on the straight grain. You can also use this technique on bias cut seams, but there is a chance of ‘bubbling’ in the fabric, so if in doubt do a trial run first.

katherine_sheers_02

What you’ll need to gather:

  • All the basic materials needed to make your knickers
  • Plus 30cm of narrow lace trim, at least 10mm wide

katherine_sheers_03

First I’m going to split the front pattern piece into three sections. This paneling is a great technique in itself, especially if you have small scraps of fabric you’d like to use up. Just ensure you keep the grainline direction consistent across all the panelled pattern pieces.

Measure approximately 3cm out from the Centre Front along the waistband and draw a diagonal line down to meet the legline (as above).

katherine_sheers_04

Cut along this line, then tape a strip of 10mm wide paper along both edges to create the French seam allowance (shown above in lilac). Label the pattern pieces, clearly marking the new grainline.

katherine_sheers_05

Lay the paper pattern pieces together as above, aligning what will be the stitching lines  (10mm in from each edge).

katherine_sheers_06

Trim the excess corners of seam allowance paper so they look something like the photo above when opened back out.

katherine_sheers_07

Lay and cut out your pattern pieces (for clarity, I’m only showing the front pattern pieces of the knickers here).

katherine_sheers_08

Lay your front panel and one of the side panels, wrong sides together and sew a line of lockstitch using a 5mm seam allowance. Trim the seam allowance to 2-3mm in width.

katherine_sheers_09

Lay your narrow lace trim, wrong side uppermost on top of your trimmed seam allowance with the flat edge sitting parallel to your stitch line. Pin and topstitch in place.

Open the panels out and press the seam flat with the lace trim pointing away from the Centre Front.

katherine_sheers_10

Turn the front and side panels right side to right side, and finish your French seam by sewing another 5mm wide line of lockstitch. This will effectively ‘trap’ the lace inside the seam.

katherine_sheers_11

Topstitch along the edge of the front panel (stitching through the French seam) to encourage the lace trim to sit flat. Then trim the ends of the lace in line with the fabric pattern pieces.

katherine_sheers_12

Repeat with the other side panel and you’re done. It’s as simple as that!

Now just treat these joined pattern pieces as a single front panel and make up the rest of your knickers as usual.

katherine_sheers_13

I’ve used French seams in this tutorial, firstly to make this technique possible for anyone who doesn’t own an overlocker, and secondly, because although they take a little longer than a standard seam, they’re an exquisite way to finish a beautiful item of lingerie.

This lace insertion can be used to create dainty detail in many garment areas. It can be added to existing garment seams such as the side seam join between a bra cradle and wing, or the waist seam join between a slip bodice and skirt. Just remember that it does add a little extra bulk so use lightweight lace (this isn’t the time to stash-bust any guipure you may have!).

I can’t wait to see where you use this technique. Please do add the hashtag #sewlingerie if you’d like to share your makes with me.

Enjoy Lingerie Sewing Month everyone!

KS x

Advertisements

6 thoughts on “Inserting a Lace Trim Tutorial

  1. Thanks Katherine! fantastic technique- I love when things are as finished and beautiful on the inside as they are on the outside! I’ll definitely be trying this out!! Also I just had a massive pinning spree from your lingerie board on Pinterest *swoon*! Thanks again! 🙂

    1. Aww thank you Erin! It’s sounds as though you’re a kindred spirit…I think the nature of sewing small pattern pieces for lingerie makes you more inclined to pay attention to the finishing. I love that you’re going to try this out! And hurrah about Pintrest, although *shame-face* I REALLY need to finish properly organising my boards! I love that it’s inspired you though. x

  2. I can’t wait to try this out! I wonder what lace I have in my stash… hmmm… Thanks so much for writing this post! 🙂

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s